Call Today

 

Right here in the next paragraph you can discover more quality additional info with regards to Tools You Need to Install a New Bathtub .

Setting up a bath tub isn't exactly brain surgery, however it does require strong plumbing, woodworking, and occasionally, tiling abilities. Changing an old bath tub with a new one is also a reasonably challenging task. If the old tub is conveniently available, the task can relocate rapidly; if you have to open up a wall to remove the old tub and place the new tub, the job is much harder. In either case, the job is within a residence handyman's skills, although you will need an assistant to leave the old bathtub as well as embeded in the brand-new one. Ensure you have actually certified yourself for the task as well as fit attempting it. Instead of hiring a contractor to take control of a halfway-completed task, it is far better to think about employing one before you begin. Possibilities are you may need a professional plumber to make tube connections.
This article will certainly aid you mount a brand-new bathtub in your restroom if you have currently gotten a new tub and also do not need to transform the plan of your previous water system pipelines.
Your devices as well as material list ought to consist of the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Preparing for the Setup

Firstly, the sustaining structure supplied with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets system to prevent stress on the bathtub.
Fit the versatile faucet adapters to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its final setting.

 

 

Removing Old Touches

If you need to change old faucets with brand-new ones as a part of your installation, after that the first thing you should do is separate the water. After doing so, turn on the taps to drain pipes any water remaining in the system. The procedure of getting rid of the existing faucets can be rather problematic as a result of the restricted accessibility that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the staying water that will certainly come from the pipes. As soon as the supply pipes have been eliminated, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this procedure. When the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Prior to carrying on to fit the brand-new taps, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

 

 

Installing the Tub

Making use of both wood boards under its feet, put the tub in the needed setting. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub until the level checks out degree.
To set up faucets, fit the bottom of the outermost versatile faucet port to the ideal supply pipe by making a compression join; after that do the very same for the other tap.
Turn on the water supply as well as inspect all joints and brand-new pipework for leakages as well as tighten them if needed. Load the bath tub and also inspect the overflow electrical outlet and also the normal outlet for leakages.
Finally, take care of the bathroom paneling as described in the supplier's instruction manual. Tiling as well as sealing around the tub ought to wait up until the tub has been used at least once as this will certainly resolve it right into its final position.

 

 

Fitting New Touches

If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin making certain that the washing machines remain in area in between the faucet as well as the sink. Protect the faucet in position with the maker offered backnut. When the tap is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet ports. The previous kind must be connected to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.

 

 

Tiling Around the Bathtub

In the location where the bathroom satisfies the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, resulting in complications with moisture and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your components and also fittings. They are offered in tubes and also cartridges, and also are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly load the tub with water before sealing, to allow for the activity experienced when the bathtub is in usage. The sealer can break rather very early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily readily available on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or water-proof sticky and cement.

 

Bathtub Installation

 

How Important Is A Bathtub To Your Home?

 

High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.

 

Install Piping Before Tub

 

You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.

 

Position the Tub

 

Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.

 

Assemble Drain Connections

 

Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.

 

Place a Pipe For the Shower Head

 

First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.

 

Attaching Hot and Cold Water Lines

 

Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.

 

Install the Spout

 

Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.

 

Check For Leaks

 

Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.

 

estore the Bathroom Wall

 

Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

 

I hope you enjoyed reading our section on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a ton for taking the time to read our blog post. Remember to take the time to distribute this write-up if you liked it. Many thanks for taking the time to read it.

Pro help, one ring away.